Interesting

How do I connect to hive hub?

How do I connect to hive hub?

Connect the hub to the household’s broadband router using the network cable provided. Fit the power cable into the hub and plug it into a power socket. Wait for the middle light to flash AMBER. During start-up the GREEN light will flash, followed by the AMBER light.

Can I install Hive thermostat myself?

Can I install Hive myself? Yes you can. Hive installation is pretty easy yourself, will save you the cost of an engineer and should only take about an hour to complete.

How do I connect Hive to central heating?

Connect the Hive hub up to your broadband router using the network cable provided. Then fit the power cable into the hub and plug it into a power socket. Before you go any further, make sure the mains supply to the central heating is off.

Is Hive Wired or wireless?

Hive Active Heating 2 Wireless Thermostat It’s wireless so you can move it around your house and make sure the temperature is right where you are. If you have a conventional boiler you can also use it to control your hot water. It takes 4x AA batteries.

How do I know if my Hive Hub is connected?

Go back to ‘Menu’ in the Hive app, tap ‘Manage devices’ then refresh the page. If the hub is showing as ‘connected’ you’re done!

Why is my Hive Hub not connecting?

Unplug Hub 360 from the wall socket and reinsert it, wait for the hub to reboot (this can take about 10 minutes) then refresh the Hive app dashboard page in the app. Step 4. You can reconnect the hub to your Wi-Fi by going to your Hive app, tap the Hub 360, Settings, Change Wi-Fi, and follow the in app instructions.

Is there a monthly charge for Hive?

Hive Live is a monthly subscription service that gives you the following benefits: Ongoing warranty on all of your Hive products. 10% discount when you buy any Hive products. Free delivery on all orders.

Where is the best place to put a Hive thermostat?

Aim for around 1-1.5m from the floor and away from heat sources such as radiators and direct sunlight. To make accurate temperature readings, your thermostat needs a free flow of air so please ensure you place in an area not covered by curtains or similar objects.

Why is my Hive thermostat not connecting?

Hold the central heating button down on the receiver until the status light flashes pink. Release the button then press and hold it again until the status light is double flashing amber. To reconnect the receiver to your hub, put your hub into pairing mode by selecting ‘Install devices’ in the Hive app menu.

How do you use Hive heating manually?

How do I change the heating mode on my Hive Active Heating 2…

  1. Push the dial to wake up the thermostat.
  2. Once the screen turns on press the Menu button and select Heat.
  3. Here you’ll see the different modes: Schedule, Manual and Off.
  4. Select one by turning and pushing the dial.

Does Hive need to be connected to router?

Our newest hub, Hive Hub 360 connects via Wi-Fi, our other hubs need to be physically connected to your broadband router using a network cable (provided with the hub) to allow you to control your Hive products remotely.

Can Hive be battery powered?

Hive Active Heating 2 is a little simpler, with four AA batteries powering the thermostat. This makes placement easier; you can put the thermostat on any wall that you like. Hive quotes battery life at around two years. Both devices can be self-installed if you’re a competent DIYer.

How do I connect the hub to my hive device?

Then connect the hub as follows: Firstly connect the hub to the household’… Installation and start-up. The hub Do not disconnect the hub. If flashing multi-coloured is attempting to connect to the continues after 5 minutes, contact Technical Hive servers and update itself. Support to confirm that it has connected. Amber Flashing Installation.

How do I connect my hive receiver to my central heating system?

Restore power to the central heating backplate, remove it completely and wire in the system – the receiver’s status light should Hive receiver in its place. If needed, you can use flash amber. This means it’s ready to a stand-off (SLS1, supplied separately) to create connect to the hub and thermostat.

How do I contact hive installation support?

Page 2 Important note: Technical Support If you need to contact Hive’s Installation should only Technical Support team during ever be carried out by the installation, you can do so a qualified engineer. on 0800 980 8614.

What is the IEE Wiring Regulations for hive?

BS7671 (IEE Wiring Regulations), Part ‘P’ of the Building Regulations and any relevant Technical Operational Procedures. Dual channel The Hive receiver is double insulated so doesn’t receiver need an earth connection.